Introduction to Nanjing Bonner Electrode Humidifier

Nanjing Bonner Technology Co., Ltd. is a well-known industrial humidifier manufacturer in Jiangsu Province. The Bonner brand electrode humidifiers produced are a new generation of environmentally friendly and efficient industrial humidifier products independently developed based on advanced production experience of electrode humidifiers from domestic and foreign peers. The product has multiple advantages, such as accurate humidification accuracy, large humidification capacity, stable and reliable operation, high degree of automation, and low maintenance costs. Widely used in factory workshops, office buildings, high-end residences, hospitals, laboratories, and other places. The installation methods are flexible and diverse, and can be directly installed in the place of use for humidification, or indirectly installed in the central air conditioning unit for humidification.

Working principle of Bonner electrode humidifier

Electrode humidifiers generally use automated control methods, sensing changes in environmental humidity through a humidity sensor. According to pre-set control parameters, when the environmental humidity is lower than the pre-set low humidity value, the humidity sensor sends a humidification signal to the controller. After receiving the humidification signal, the controller first opens the inlet solenoid valve to allow tap water to enter the humidification tank. The water level in the tank continues to rise and comes into contact with the electrified electrode rod. The current uses the ions present in the tap water to form a circuit, and the high-intensity current causes the water in the electrode tank to quickly heat up to boiling, producing a large amount of water vapor that is output to the receiving environment through the steam delivery pipe, increasing the environmental humidity. With the output of steam, the water level in the humidification tank continues to decrease. At this time, the controller will open the inlet solenoid valve again to replenish tap water. When the controlled environment humidity reaches the pre-set value, the electrode humidifier will automatically clean the humidification bucket and turn off standby.

Model designation of electrode humidifier:

Usage conditions of Bonner electrode humidifier:

1. Environmental temperature requirement: above 5 degrees Celsius and below 40 degrees Celsius.

2. Environmental humidity requirement: The usage environment humidity must be less than 85RH.

3. The inclination angle between the installation surface and the vertical surface is less than ± 5 degrees.

4. Use clean tap water or softened water that is not replaced with industrial salt as the water source for humidification. (Conductivity 125~1250us/cm2, water hardness not exceeding 30 German degrees)

5. Water supply pressure: If the pressure is greater than 0.1 megapascals and lower than 0.5 megapascals, a pressure reducing valve should be equipped for excessively high inlet pressure.

6. Interface size: DN15G1/2

Characteristics of electrode humidifier

1. The Bonner electrode humidifier adopts an automated control system and intelligent humidification.

a. Easy to operate, users can choose between switch and analog control modes according to different control methods.

b. Proportional adjustment control board: Interface signal is 0~10VDC, humidification efficiency is 100%, and the humidification amount can be controlled within the range of 20~100%. According to the different conductivity of water and changes in indoor humidity, adjust the humidification ratio in a timely manner, control the humidification amount, and keep the humidity constant within the set humidity range. At the same time, the humidifier has an automatic cleaning function, which can automatically adjust the drainage cycle inside the humidifier according to changes in the soluble mineral content (conductivity) of the water in the humidifier, extending the service life of the humidifier.

2. Framework structure

a. The humidifier frame has high strength and strong impact resistance.

b. Galvanized panels have advantages such as corrosion resistance and resistance to scratches.

3. Fan (suitable for direct humidifiers). When using direct humidification method, the Bonner steam distributor selects high-quality fans, which have the advantages of low noise, stable operation, corrosion resistance, low power consumption, and long service life.

4. Electrical components

All electrical components are selected from world-renowned brands such as ABB and SCHNEIDER, with good performance and reliable quality

5. Complete range of models: humidification capacity covering 4kg/h-126kg/h

6. Fast humidification speed: can quickly generate steam and achieve the humidification target in a short time;

7. Safety and hygiene: Using steam humidification method can kill pathogens and bacteria that may exist in water, ensuring reliable hygiene, especially suitable for use in hospitals, high-end office buildings and other places.

Selection Table for Electrode Humidifiers